You are here:>>VAC8010F-80V non-functioning KWH display
VAC8010F-80V non-functioning KWH display 2018-06-17T04:32:12+00:00

Home Forums DROK Customization VAC8010F-80V non-functioning KWH display

Viewing 15 posts - 1 through 15 (of 28 total)
  • Author
    Posts
  • Dale Kramer
    Post count: 0

    I have two of these and am able to set BAT and BPC to be able to watch capacity in AH and % count down to 0.

    I have not been able to get KWH to show anything but 0. The time (8) on display description does count up after doing a RET but KWH does not.

    How do I get KWH to work?

     

    Drok
    Keymaster
    Post count: 2971

    Hello Dale Kramer,

    Is it this item? https://www.amazon.com/dp/B07B1SJ8W6

    Did you use it in charging or discharging mode.

    Best regards.

    Dale Kramer
    Post count: 0

    Ah, now I see that KWH only increments positively when the current is positive.

    What is the reason that it does not measure KWH of discharge?

    Drok
    Keymaster
    Post count: 2971

    Hello Dale Kramer,

    In charging mode, kwh value increases. In discharging mode, it dicreases. When it is 0, it will not change again.

    Best regards.

    George
    Post count: 0

    <p style=”text-align: left;”>Hi, mine won’t connect to wireless, just greyed out after a few seconds.</p>

    Drok
    Keymaster
    Post count: 2971

    Hello George,

    Is it this item 2001802003?

    Does greyed out mean screen turns off? To check problem for you, would you please kindly take a video to show how it is? You can share video link here or send it directly to service@droking.com

    Best regards.

    George
    Post count: 0

    <p style=”text-align: left;”>Hi, I don’t get any voltage or parameters on screen just all zeros. As if it doesn’t connect to module. Can get a video tomorrow.</p>
    Regards

    George

    Drok
    Keymaster
    Post count: 2971

    Hello George,

    You can  check  wireless communication indicator  on the left bottom of display .And is the load and power supply  connected well with module?

    Best regards.

    Pike
    Post count: 0

    How do you calibtate these meters?

    Drok
    Keymaster
    Post count: 2971

    Hello Pike,
    May I know more details about your problem?
    What parameters do you want to calibrate?
    Best regards.

    Andy
    Post count: 0

    I have installed the unit, appears to be working but the battery charge state isn’t working. If I set the capacity at zero, it shows as fully charged, but anything more than zero the remaining capacity graph drops to zero even if I set a greater than zero value for BPC.

    Drok
    Keymaster
    Post count: 2971

    Hello Andy,

    Are you talkikng about above item? 2001802003?

    Did you  program BPC parameter only? How is BAT setting?

    Best regards,

    DROK

     

    Michael Ward
    Post count: 0

    i just purchased  vac8010f

    i’am very disappointed at wifi range of about 3 yrds,  with out any walls.

    Can I extend the little plugin wifi unit 6 wires on the transmit end ?  shielded cable?

    If so what is the max length ?

    Please send the schematic or pin-out.

    thanks

    be safe

    michael

     

    Drok
    Keymaster
    Post count: 2971

    Hello Michael Ward,

    Do you mean this item?

    https://www.droking.com/Digital-Meter-Multifunction-Panel-Meter-DC-6V-80V-300A-999-KW-LCD-Display-Tester-Monitor-Meter-Multimeter-Thermometer

    Sorry, we are not sure the 6 wires you mentioned. Would you like to show it by image?

    Best regards,

    DROK

     

    • This reply was modified 4 years, 1 month ago by  Drok.
    michael ward
    Post count: 0

    Hi

    Working on and off now but range is 15 feet with extended wifi radio on sensor end, 8 wires not 6.

    Also put bypass cap on radio dc input on sensor end.

    I ordered more powerful radio for both ends with hope that extends com range

    My system is 120V dc batteries 225Ah with wind and solar charging  bat range 113-145V, current =0-25A

Viewing 15 posts - 1 through 15 (of 28 total)
Reply To: VAC8010F-80V non-functioning KWH display
Your information: