You are here:>>Manuals, schematics, etc for product(s)
Manuals, schematics, etc for product(s) 2017-05-10T23:03:42+00:00

Home › Forums › Voltage Regulator Support › Manuals, schematics, etc for product(s)

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • Joe
    May 10, 2017 at 11:03 pm
    Post count: 0
    #16945 Reply |

    Im looking for the manual to the product https://smile.amazon.com/gp/product/B01MSJQAKY/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

    The item doesnt seem to be listed anywhere on the drok site, and it seems impossible to find on google without a specific model.

    Beyond asking for the manual, can I urge Drok to make their listings more helpful? Most the products on the amazon store require some serious searching to find more information on, such as manuals.

    Also, I assume a lot of customers are electronics nerds who would absolutely love conveniently found schematics. Or even the source code for the controllers. I understand why that kind of stuff might not just be given out, but hey, its an idea.

    Drok
    Keymaster
    May 11, 2017 at 10:04 am
    Post count: 2971
    #16987 Reply |

    Hello Joe,
    Thank you for writing in.
    Here is an PDF instruction for your reference.
    200220
    For more question, please let us know.
    Best regards.

    John Petre
    May 22, 2017 at 6:42 am
    Post count: 0
    #17501 Reply |

    I need the hook up diagram for Drok 100413 voltage current meter. My meter is only reading current when charging the battery. No current reading when drawing from the battery.

    Jay C Reynolds
    May 22, 2017 at 8:47 pm
    Post count: 0
    #17536 Reply |

    DROK DC 12V Digital Timer Relay Board, Automotive 1500W Relay Module with Dual Time Display, Timing Relay Switch, Support Cycle of time, Time Delay for Car, Vehicle Sold by: DROK

    Where can I get a manual for this unt?

    Thank you,

    Jay

    Drok
    Keymaster
    May 23, 2017 at 6:58 am
    Post count: 2971
    #17546 Reply |

    Hello Jay C Reynolds,
    Thank you for writing in.
    Are you talking about this item?
    https://www.amazon.com/DROK-Digital-Automotive-Display-Support/dp/B01MZ8DIOM/ref=sr_1_1?ie=UTF8&qid=1495500621&sr=8-1&keywords=DROK+DC+12V+Digital+Timer+Relay+Board%2C+Automotive+1500W+Relay+Module+with
    Here is an instruction for your reference.
    300456
    For more questions, please feel free to contact us.
    Best regards.

    Drok
    Keymaster
    May 23, 2017 at 1:04 pm
    Post count: 2971
    #17556 Reply |

    Hello John Petre,
    Here is a wiring diagram for 100413.
    100143
    Best regards.

    John Petre
    May 24, 2017 at 3:04 am
    Post count: 0
    #17587 Reply |

    Thank you for the quick response. The documentation I received had 4 options, all very similar, and this is the one I chose. I verified my installation and it is correct per your drawing. Yet I am only measuring current into the batteries from the solar controller. My install is using the DROK meter to measure 4, 3.2volt, 100 AH CALB Li batteries in Series driving a 45 lb Thrust trolling motor, fish finder and other accessories on my Kayak. I have plans for 200 watts of solar cells driving two DROK DC to DC converters for charging. I have installed the DROK converters and are using them to charge the batteries with an external DC power supply. The trolling motor does have a pwm controller built in. Could this be affecting the meters ability to measure current? Does the meter current in and out of the battery?

    John Petre
    May 24, 2017 at 4:53 am
    Post count: 0
    #17597 Reply |

    Never mind my last message. I just hooked up one of my bait tank pumps and the meter is showing + .9 amps. So it must be the pwm controller that is causing the meter to not read the proper current. Any DROK products that will correctly read pwm current?

    Drok
    Keymaster
    May 24, 2017 at 9:37 am
    Post count: 2971
    #17625 Reply |

    Hello John Petre,
    Thanks for your reply.
    We are sorry so far we don’t have product can read read pwm current.
    Hope you can understand.
    Best regards.

    John Petre
    May 24, 2017 at 11:51 am
    Post count: 0
    #17640 Reply |

    Thanks again for helping me figure this out. One more question. Is there any reason why not to just jumper 2 and 3 on the drawing?

    Drok
    Keymaster
    May 25, 2017 at 9:47 am
    Post count: 2971
    #17727 Reply |

    Hello John Petre,
    Terninmal 2 and Terninmal 3 are not in the same circuit.
    Terniamal 2 is connected to a circuit with shunt.But terninmal 3 doesn’t need to connect with shunt.
    Best regards.

    David peyvan
    May 25, 2017 at 2:22 pm
    Post count: 0
    #17750 Reply |

    I need technical manual for qs-1212cba-150w

    John Petre
    May 25, 2017 at 11:41 pm
    Post count: 0
    #17794 Reply |

    Are not both actually at the – battery/power source potential at the negative connection point on the shunt?

    Drok
    Keymaster
    May 26, 2017 at 8:45 am
    Post count: 2971
    #17825 Reply |

    Hello John Petre,
    They just use the common negative, but they are not in the same circuit.
    If you connect 2 and 3 directly, that will have influence on current measurement。
    Best regards.

    Drok
    Keymaster
    May 26, 2017 at 8:47 am
    Post count: 2971
    #17826 Reply |

    Hello David peyvan,
    Thank you for writing in.
    Would you please tell us the ASIN/part number of item?
    Or you can just send us the link for confirmation.
    We will find solution for you at that time.
    Best regards.

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 15 total)
Reply To: Manuals, schematics, etc for product(s)
Your information: