You are here:>>support manual
support manual 2017-06-05T12:04:29+00:00

Home Forums Advice support manual

Viewing 15 posts - 1 through 15 (of 26 total)
  • Author
    Posts
  • Isaac Atison
    Post count: 0

    Kindly provide me manal for Dual Display DC Digital Multimeter Voltage Ampere Meter LCD Digital Display Voltmeter Current Meter with Shunt Volt Meter DC0-600V Amp Meter 0-100.0A for Battery Chargers Electric Vehicles to enable me connect it to my solar systeml

    Drok
    Keymaster
    Post count: 2641

    Hello Isaac Atison,
    Thanks for writing in.
    Is it the item you are talking about?
    100422
    Here is an instruction for your reference.
    PDF
    For more questions, please let us know.
    Best regards.

    Barry Greengrass
    Post count: 0
    Drok
    Keymaster
    Post count: 2641

    Hello Barry Greengrass,
    This is instruction for item#200150. Hope it can help you.
    200150 pdf
    Best regards.

    Ed Quittkat
    Post count: 0

    Hello: I purchased a 300482 Adjustable voltage /current calibrator. I also built a battery pack to make it portable. I would like to add a sliding switch to turn the unit on and off. Do you have a schematic or pdf file for helping me add a switch?

    Drok
    Keymaster
    Post count: 2641

    Hello Ed Quittkat,
    Thank you for writing in.
    Do you mean you want to use a switch to control the power supply for this module on/off?
    If yes,there is a solder joint place for controlling power on/off.
    You can try to remove D2 diode and install it to D1. Then use leading wire to transfer the positive pole of D2 the position of Power on/off and shorted the botton part of the solder joint place of Power On/off.
    Here are some images for referrence:
    001
    002
    003
    004
    005
    006
    Hope this can help you.
    If there is any question, please feel free to contact us.
    Best regards

    Ed Quittkat
    Post count: 0

    That’s exactly what I needed, Thank you!

    Now, if I can find a micro switch.

    Drok
    Keymaster
    Post count: 2641

    Hello Ed Quittkat,
    You’re welcome.
    Please note that this micro switch is not included with the product.
    It is just an example to show how to add a switch.
    And sorry that we do not have the switch for sale.
    Hope you can understand.
    Best regards

    Gary Wright
    Post count: 0

    I purchased the Green Mini Volt Capacity Monitor (product # 200311) on Amazon. The instructions were not included when shipped. Could you please give me a link to the instructions in a PDF file?

    Drok
    Keymaster
    Post count: 2641

    Hello Gary Wright,
    Thanks for writing in.
    We have attached instruction on Amazon product page.
    Here is the link to it.
    https://images-na.ssl-images-amazon.com/images/I/91BFCr+r8vL.pdf
    Best regards.

    Gary Wright
    Post count: 0

    Thank you – just what I needed. The OK button/switch on front side not operating so I can’t change any of the settings. Any ideas on how to fix this?

    Drok
    Keymaster
    Post count: 2641

    Hello Gary Wright,
    Please can you tell us what the problem is?
    If you can, would you please take a short video to show us the problem?
    You can try to upload video on Youtube and share us the link. Or you can also send it directly to our service email(service@droking.com)
    Best regards.

    Ed Quittkat
    Post count: 0

    Hello I purchased the 300482 4-20/0-10V signal generator calibrator. I cannot get more than 13.6 mA out of the current calibrator. The 0-10V section works fine. Is  there any adjustments   that I can do . The displays are adjusted correctly and the meter I am using for calibration is ISO 9000 certified.

     

    Drok
    Keymaster
    Post count: 2641

    Hello Ed Quittkat,
    Thanks for writing in.
    Have you test the actual current value with multimeter? Is the actual value the same to the display?
    Best regards.

    Ed Quittkat
    Post count: 0

    As I said the multimeter is a certified Fluke 187. The display matches the output. But the output on the current scale will not go above 13.6 mA. The display matches the output. You should provide a new board if you don’t have any solutions.

Viewing 15 posts - 1 through 15 (of 26 total)
Reply To: support manual
Your information: