You are here:>>What regulator do I use for my Aptronics GPS. I need to keep the 13 volts consta
What regulator do I use for my Aptronics GPS. I need to keep the 13 volts consta 2016-08-07T03:08:10+00:00

Home Forums Voltage Regulator Support What regulator do I use for my Aptronics GPS. I need to keep the 13 volts consta

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • Tom
    Post count: 0

    My Mercedes has a varing voltage of 12 vdc to 13.8 vdc. My new mirror GPS requires 13 constant voltage. I will be placing this in my trunk next to the fuse box. Also the voltage regulator must be a set and forget type. I can not adjust it everyday. Only once on installation.
    I am installing a Smartnav 5 GPS. By apptronics.

    Would you also have a relay that would prevent my power antenna from extending when I turn the ignition on, then it goes back down after I start the car. With a delay relay of approximately 10 seconds I can start the car then when I want the stereo on only then will the antenna extend.

    Thanks for your help,
    Tom

    Drok
    Keymaster
    Post count: 2971

    Hello Tom,
    Thank you for your interest in our product.
    Here are the recommendation for you:
    For the voltage regulator:
    Part number:#200151
    DROK® Numerical Control Voltage Regulator Buck Boost Converter, DC 10-40V to 0-38V 6A Constant Voltage Current Step Up Step Down Transformer, Variable DC Power Supply with LED Display
    Parameters:
    Input voltage: DC 10-40V
    Output voltage: DC 0-38V
    Output current: 0-6A
    Conversion efficiency: 92%
    Working frequency: 150KHz
    Short circuit protection: constant current
    Operating temperature :﹣40℃~+85℃
    Control method: numerical control + digital tube display
    Voltage regulator/display resolution: 0.01V
    Minimum resolution of power display: 0.001W
    Current regulator/display resolution: 0.001A
    Minimum resolution of capacity display: 0.001AH
    Output ripple: ≤50mV
    Weight: 116g
    Dimensions: 100×80×21mm

    Features:
    1. Adopts advanced microprocessor, can regulate output voltage and current accurately;
    2. Can step up and step down the voltage;
    3. All display by digitals, convenient and easy to use;
    4. Has constant voltage and constant current statue;
    5. Uses 4 digits high brightness LED, can display output voltage, current, power and capacity and other parameters;
    6. Voltage, current, power, capacity and other parameters can be switched to display automatically or manually;
    7. Has output OUT, constant voltage CV and constant current CC indicators;
    8. Can be set whether to output automatically when power on;
    9. The set voltage and current values can be saved by key;
    10. Has memory saving function, can store 10 groups of parameters and they can be freely stored and called out;
    11. The maximum input current is 8A under step up mode, when the output voltage is much larger than input voltage, the output current may not be up to 6A.

    For the relay:
    Part number: #200088
    DROK® Multifunctional DC 12V 1 Channel Relay Board Single-channel Relay Module 10A Portable Timer Switch Board Power Switch Circuit with 18 Mode and LED Digital Display Cyclic Time Delay
    Parameters:
    Input voltage: DC 12V
    Control voltage: AC 0~250V / max.10A; DC 0~30V / max. 10A
    Size: 2.59×1.57×0.67 inches

    Module Functions:
    The 18 functions include:
    close or disconnect upon a certain set time;
    limitless cycle timing mode 1 and 2 (cycle time 0.1 seconds to 270 hours adjustable);
    self-lock relay mode;
    trigger relay mode;
    limited cycle timing mode 1 and 2(0.1seconds to 9999 seconds adjustable.).
    Note: Functions 1-8 automatically start at power on;
    functions 9-18 require high pulse signal (duration time no less than 20ms) trigger to start.

    Timing pull
    Timing disconnect
    Timing pull then disconnect
    Timing disconnect then pull
    Limitless cycle timing mode 1 and 2
    Limited cycle timing mode 1 and 2
    Self-lock relay mode
    Trigger relay mode
    Trigger timing pull
    Trigger timing disconnect
    Trigger timing pull then disconnect
    Trigger timing disconnect then pull
    Limitless cycle timing mode 1 and 2
    Limited cycle timing mode 1 and 2

    Hope this can help you.
    Best regards

    Tom
    Post count: 0

    Thank you for the information on your products.
    I am putting them both in my car so I need some protection for them. Do you have a case that will protect them and act as a heatsink so it will not overheat in the summer if they get hot.
    Also do you have a discount code that I can use? I will be buying 2 of each with matching protection cases.
    Thank you for your support
    Tom

    Drok
    Keymaster
    Post count: 2971

    Hello Tom,
    You’re welcome.
    So sorry that we do not have such a case can meet your demand.
    And this two product are not included in our promotion plan right now, we cannot provide a discount code for you.
    Beg your understanding.
    Best regards

    Tom
    Post count: 0

    Thank you for the info. Do you have the mounting screws/nuts for them, with small stand off spacers? I will have to create my own box but I need the proper mounting hardware so that they do not move and short out. Do have any type of protection case at all? Tom

    Tom
    Post count: 0

    Can you also provide proper wiring diagram for both products, including any online videos that might help me. I don’t want to burn it up by accident. Tom

    Drok
    Keymaster
    Post count: 2971

    Hello Tom,
    For the #200151, there are four screws attached on the board.
    For the #200088, so sorry that we do not have screws providing for you, but you can use to fix it.
    Please note that the bottom of the board(#200088) need to be insulated.
    Here the PDF files are the datasheet of the products:
    DATASHEET_200151
    DATASHEET_200088
    Hope this can help you.
    Best regards

    Ben Brand
    Post count: 0

    Looks like

    http://www.droking.com/wp-content/uploads/2016/07/Instruction_200151.pdf

    Does not lead anywhere anymore. Has this moved to a new page? looking for information about the “Fully functional” mode and how to use it

    Thanks, Ben

    Drok
    Keymaster
    Post count: 2971

    Hello Ben Brand,

    Here is 200151 instruction for your reference.

    https://www.droking.com/cs/wp-content/uploads/2020/05/200151-instruction.pdf

    Best regards,

    DROK

Viewing 9 posts - 1 through 9 (of 9 total)
Reply To: What regulator do I use for my Aptronics GPS. I need to keep the 13 volts consta
Your information: