Forum Replies Created
-
AuthorPosts
-
in reply to: 8-60V 15A Buck Boost Converter #19644
Hello Mark,
Thank you for writing in.
Are you taling about the same item?
200150
May I know more details about your setting? For example, input voltage/current, which function do you choose?
It would be more helpful if you can take a short video to show your operaton.
You can send it to service#droking dot com ( please replace # with @)
Best regards.in reply to: Buck reg YH11060D won't start with load connected #19637Hello Tomt,
Thanks for writing in.
We are sorry we can’t confirm the item you mention. All of items have ASIN number and SKU number. Is it convenient for you to find out one of them from your order information?
Or you can just send us your order ID.(If you don’t want to show order ID here, please send it to service#droking dot com ( please replace # with @))
We will try our best to find solution for you once we confirm the item.
Best regards.Hello Nicole,
Thanks for writing in.
We can’t ensure if it is the following item you mentioned.
090945
If yes, would you please tell us more details about your problem? For example, the input voltage.
This item only have two buttons, low power button and USB output button. Which one do you mean? Can’t it output voltage?
With your help, we can find out problem as soon as possible.
Best regards.in reply to: drok speaker #19616in reply to: manuals for your product #19572Hello rolf oetter,
Thanks for writing in.
Sorry for inconvenience caused on you. This is a semi product, so we don’t have paper instruction.
Here is a simple instruction for your reference.
090063
Hope it can help you.
Best regards.in reply to: F900S Firmware #19545Hello Darren,
Thanks for writing in.
It’s regretted the name can’t be modified by our customers.Hope you can understand.
Only customized product have different name.
Best regards.in reply to: Timer 200119 #19544Hello Louis MAttos,
Thans for writing in.
We are sorry this item doesn’t have countdown function. The time can be only incrementing.
Hope you can understand.
For more questions, please feel free to contact us.
Best regards.Hello j_z_j,
Thanks for writing in.
Are you talking about this item?
090155We are sorry this item is not suitable to drive three 4Ohm 3w speakers. It is not enought to power 3 speakers in the meanthime.
For any more questions, please feel free to contact us.
Best regards.Hello jj,
This button can be used to turn on/off backlight and reset energy reading.Reset energy reading:
Step 1: Keep pressing the button for 5 seconds until the energy reading flicker, then release button;
Step 2: Short press button, the energy data will reset.
Step 3: If you don’t want to reset it, please keep pressing button again for 5 seconds until the energy reading doesn’t flicker.
Best regards.in reply to: DROK 4-20mA Signal Generator, DC 12-30V #19503Hello jessie,
Thanks for writing in.
We think you are talking abou S1 and S2 button. In general, you don’t need to use them. They are used for calibration.
If you input 24V DC power supply, the impedance range of output load is between 0-800 Ohms. It can provie 0-10V 4-20ma signal.
Best regards.in reply to: Wiring Ammeter Dual #19496Hello Lee Buxbaum,
Thanks for your business. Is this item that you have bought?
product link
You said you have attached a link, but we see no information about it. Would you please send it again?
In addition, did you write it up as the following picture showed?

Best regards.in reply to: connections for SKU:300480 #19492Hello Bill Lazenby,
Here is the wiring diagarm for your reference.
Please note there are no distinction between positive pole and negative pole.

For more questions, please feel free to contact us.
Best regards.Hello Steve McCurdy,
Thanks for writing in.
Are you talking about this item?
180051
This is a buck converter, if you input 18V, you can get output voltage under 18V.
It don’t have different requirement for litium battery.
Best regards.in reply to: DC051 wiring options #19421Hello Mike,
Thanks for your business.
It’s regretted the meter with external shunt can’t be wired up like the meter with bulit in shunt.Hope you can understand.
Best regards.Hello Jimmy lyon,
Thank you for writing in.
We are not sure if you are talking about this item200141
If yes, please long press the button, and release it until ‘CLr” shows on the power area.
At this time energy area flicker, then short press the button to reset energy.
Any more question, please feel free to contact us.
Best regards. -
AuthorPosts