Forum Replies Created
-
AuthorPosts
-
in reply to: Time delay relay latency #43933
Hello,
P1 mode: Once you connect high or low level signal, relay contact will close. Notice: relay conntact close at once instead of after signal is disconnected.
Without signal , relay contact is always opened.
We are terribbly sorry we can’t confirm your purpose about ” disable high trigger”. High or low lever siganl can trigger relay, if you don’t want to use high level port, just ignore it.
About the second problem, once power on, relay will close simultaneously. There are no time delay.
Best regards.
Best regards.
in reply to: Did I purchase the right DROK unit? #43927Hello Randy Wong,
Is it this item? #2001711007, https://www.amazon.com/dp/B078Q1624B/ref=as_li_tl?tag=proeng-20
You can step down voltage from 17v to 12v. But please kindy notice input voltage must be at least 0.8v higher than output.
And regarding current adjustment, it can only set a limit on output current. Actual output current is mainly decided by load. For example, preset value is 4.7 A. If load intend to draw 5A, it will limit current at 4.7A.
However, if load request 2A, actual output is just 2A.
Best regards,
DROK
Hello Joseph Bonsignore,
Could you please tell us which item it is? Is it below item? Are you talking about below item? https://www.droking.com/cs/wp-content/uploads/2019/04/200193.pdf
Best regards.
in reply to: Time delay relay latency #43866Hello,
We are terribly sorry we can’t confirm the “V+” you mean. Is that your signal source?
Under P1 mode, once you send high or low level signal, relay contact will close, energize time is set by user.
Without signal , relay contact is always opened.
Best regards.
Below is our thinking. Please check if it is correct.
1. The
in reply to: Time delay relay latency #43776Hello Nicholas Loes,
We are sorry we are not sure the first question. Could you please tell us more details?
Setting parameters will be saved when power off.
And regarding the last questions, there are many working mode. We can’t confirm which one you are talking about.
Could you please refer to the working modes in manual? https://images-na.ssl-images-amazon.com/images/I/91z+BlySwmL.pdf
Best regards,
DROK
Hello Chapman Flack,
We are sorry so far there are no similare items can meet the requirement of common ground.
Best regards,
DROK
in reply to: Hall effect device #43692Hello
#2001712003, https://www.amazon.com/dp/B07B4CWKRJ/ref=as_li_tl?tag=proeng-20
If you need longer sensor cable, please use shield cable, or there is impact on measurement. Connector is XH2.54-3p.
Best regards.
in reply to: Pulse Generator Serial Interface #43518Hello Robert,
We have uploaded pdf manual on product detail page, please feel free to download it.
https://images-na.ssl-images-amazon.com/images/I/A1R7QdmPRhL.pdf
Best regards.
in reply to: Drok Boost converter not working #43422Hello Jerry lee,
To give you accurate answer, could you please tell us which item it is? SKU number or product link would be appreciated.
And would you like to show us how it is by video? With more information, we can find soluiton more quickly.
Best regards.
in reply to: DC-DC Buck Converter… #43357Hello John,
According to your inforamation, the output voltage from your battery is DC 12V.
Both items can accept 12v input.
Best regards.
in reply to: Extending the wires for the CT #43244Hello Rory O’Brien,
200308 can only be used at 50Hz. CT lead can be exted to 12 inches.
Best regards.
Hello marjamar,
Thanks for writing in.
There is no such protection setting. If demand is large , you may think about custom item.
Best regards,
DROK
Hello lei,
serial port communication is availabe on 200310.
Please refer to below instruction.
https://www.droking.com/cs/wp-content/uploads/2018/10/200310.pdf
Best regards.
Hello Rob K,
Thanks a lot for your effort.
We still try our best to make it better.
Best regards.
Hello Jane,
Please check if it is #180080, https://www.amazon.com/dp/B07JZ2GQJF/ref=as_li_tl?tag=proeng-20
Here is pdf manual, https://images-na.ssl-images-amazon.com/images/I/71d9UyWTRrL.pdf
Best regards.
-
AuthorPosts