Forum Replies Created
-
AuthorPosts
-
in reply to: Integrate several DROK boards. #36472
Hello Jesus Hidalgo,
Do you mean removing all of wire connectors?
As the quantity is small, we are sorry facotry will not produce them separately for us. Would you mind unsoldering these connectors in person?
Best regards.
in reply to: Integrate several DROK boards. #36454Hello,
We can’t confirm which item it is. Would you please kindly offer a product link or othere information?
Best regards.
in reply to: I need a longer connector #36444Hello Loring Green,
We are sorry for inconvenience may cause.
We don’t have longer cable for it. You can try to find longer cable, but it must be shield cable, or it will have influence on measurement. And length is better withing in 8.2 foot.
Best regards.
in reply to: Mounting DROK pulse generator #36443Hello Philip C. Cory,
We are sorry we can’t confirm which item it is. Would you please kindly offer productl link?
Best regards.
in reply to: DPK6012 UART #36442Hello Robert O’Brien,
Please kindly check if it is this item 200310
Here is communication protocol, https://www.droking.com/cs/wp-content/uploads/2018/10/200310.pdf
Best regards.
in reply to: 0.56" DC 100A Ammeter Current #36434Hello Ronald Formosa,
We are sorry we can’t confirm which ammeter it is. Would you please offer a product link for confirmation?
Best regards.
in reply to: VAC8010F – Reset current to zero #36433Hello Søren Laursen,
Do you mean when connect your instrument to our item, the current reading is zero?
Please kindly notice “CER” is for no-load current reset. That is to say, when there is not load current, reading is stil not 0. Only in that case, you can reset it. And you need to operate it under no load.
Any more questions, please kindly contact us.
Best regards.
in reply to: Integrate several DROK boards. #36432This reply has been marked as private.in reply to: Customized programmable buck converter #36427Hello Rami Boul,
Regarding custom item, factory has requirement on quantity. Would you like to tell us how much you need?
Best regards,
Hello Ian Kilborn,
Thanks for writing in.
Would you please send the link again? We can’t find the link.
Best regards.
in reply to: Integrate several DROK boards. #36425Hello Jesus Hidalgo,
Thanks for your writing.
We are sorry it is hard for factory to make this custom time if quantity is 35 pcs.
For more questions, please kindly email.
Best regards.
in reply to: standard wall mount dimmer #36404Hello don queen,
According to the product title, we find out 300482
We ar not sure if it work for your LED. The output is voltage signal or current signal. The load capacity is small.
Best regards
Hello Mike Bilderback,
Thanks for writing in. We think it should be this item 200219
Watt hours will be reset after power off. As for AH zero clearing, please move cursor to LOP then short press down button; when there is no cursor, please short press OK button, time will be reset and AH will be reset or filled.
Any more questions, pleae kindly let us know.
Best regards.
in reply to: dc-dc converter 6-12 volt #36371Hello ron rowand,
Thanks for writing in.
Is it this item? https://www.amazon.com/dp/B01L90B3RI/ref=as_li_tl?tag=proeng-20
Could you please tell us the input current and your load current? If without load, how is it?
It would be better if you can take some images or video to show wiring and working status. You may try to send it here or to Service@droking.com
Best regards.
in reply to: DC bidirectional low voltage not working #36361Hello Thomas Tavano,
Thanks for writing in.
Could you please tell us which battery code you choose in menu 1 and voltage reading? Would you like to take a video to show your setting?In that way ,we can check it quickly.
You can share a product link or send attachment to Service@droking.com
Best regards.
-
AuthorPosts