-54% Digital Meter 12V Acid lead Batteries indicator Battery Capacity Digital LED Tester Voltmeter Adjustable Digital Panel Meter

Ask Question

It is a Digital Meter/Battery Capacity Voltmeter Tester/Adjustable Digital Panel Meter, Voltage measuring range: DC6~120V (wide range),the maximum input voltage can not exceed 120V, Suitable for Lithium and lead-acid batteries, Applications: Various instruments and meters; portable device; power bank; medical device, electromobile, self-balance car or other products Voltage Capacity measurement.

Description:
  • Suitable for battery pack based on lead-acid battery.
  • The screen can display voltage, power, percentage of electricity at the same time.(note: these three can be switched by the key.)
  • Can measure adjustable voltage range of 6-120V.( Lead-acid battery 12V for this item)
  • Anti-water and easy to connect with only two wires.
Setting Mode:
  • 1. Power on( red for + and black for - .
  • 2. Press a few seconds to setting mode: from 1-U, 2-b, 3-C to 4-d.
    • 1-U: adjust voltage
    • 2-b: setting battery type
    • 3-C: setting number of battery
    • 4-d: setting "showing mode"
  • 3. Adjust Voltage:
    • While on 1-U, press the button to enter into adjusting voltage mode, release it and press again,  volatge will be step-up adjusted; release the button and then press it to step-down adjust; Repeatly adjust and save the setting while the screen flash and exist setting.
  • 4. Adjust battery type:
    • While on 2-b, press the button to change the type of battery press one by one will showed: 1.2V__2V__3.2V__3.7V__12V ( While adjust to appropriate battery type, release the button, save and  exist setting when the screen flashing.)
      • 1.2V: NI-MH battery, each battery 1.2V
      • 2 V:  Lead-acid battery, each battery 2V
      • 3.2V: Lithium iron phosphate battery, each battery 3.2V
      • 3.7V: Polymer battery,each battery 3.7V
      • 12 V: Lead-acid battery, each battery 12V
  • 5. Setting number of batteries:
    • ◆ While on the "3-C" setting, press the button to enter into setting number of batteries.
    • ◆ Release the button and press again,value will be step-up adjusted; release the button and then press
    • it to step-down adjust; Repeatly adjust to appropriate number of batteries.
    • ◆ Save the setting while the screen flash and exist setting.
    • ◆ Different range for different type batteries:
      • 12V Lead-acid battery: 1-10 sections
      • 3.7V Lithium battery: 2-28 sections
      • 3.2V Lithium ion battery: 2-32 sections
      • 2V Lead-acid battery: 3-60 sections
      • 1.2V NI-MH battery: 10-70 sections
  • 6. Setting showing mode:
    • ◆ While on "4-d", press the button to enter into setting showing mode.
    • ◆ Release the button, press it once showed one mode: V - voltage, % - percentage of power( these two
    • will be in cyclic display)
    • ◆ Adjust to appropriate mode,save the setting while the screen flash and exist setting.
  • 7. Samples for setting:
    • 12V Lead-acid battery( 1 section 12V series): sellect 12.0 on "2-b" setting, sellect 1 on "3-c"
    • 24V Lead-acid battery( 2 section 12V series): sellect 12.0 on "2-b" setting, sellect 2 on "3-c"
    • 36V Lead-acid battery( 3 section 12V series): sellect 12.0 on "2-b" setting, sellect 3 on "3-c"
    • 56V Lead-acid battery( 28 section 2V series): sellect  2.0 on "2-b" setting, sellect 28 on "3-c"
  • 8. Technical Parameters:
    • Voltage measuring range: DC6~120V (wide range),the maximum input voltage can not exceed 120V
    • Test voltage: DC6~120V (decimal point automatic shift)
    • The minimum resolution below 100V: 0.1V
    • The minimum resolution of 100V: 1V
    • Power Resolution: 1%
    • Working current: <20mA
    • Display mode: LED display
    • Exterior dimension: L54 x W30 x H21mm
    • Opening hole for installing: 47.2 x 27.3mm
    • The measurement rate: more than 500mS/ times
    • Voltage measurement accuracy: 1% (2 digits)
    • Lead length: >150mm
    • Minimum supply voltage: +6V
    • Maximum power supply voltage: +120V
    • Operating temperature: -10 ~ +65
    • Working humidity: 10 ~ 80% (no condensation)
    • Working pressure: 80 ~ 106kPa
Note:
  • This tester for Lithium and lead-acid batteries Universal ,the factory default setting for 12V lead-acid battery power and voltage cycle display,If you need to test other specifications can be re-set by yourself.
Package includes:
  • 1 x Indicator Battery Capacity Tester

Attributes
input voltage120V
output ways1

Write a review

Please login or register to review

Digital Meter 12V Acid lead Batteries indicator Battery Capacity Digital LED Tester Voltmeter Adjustable Digital Panel Meter

  • Brand: Drok
  • Product Code: 200073
  • Availability: In Stock
  • $19.50
  • $8.88
  • Bulk Buy Discounts. Buy more please contact us
    Qty51020+
    Price$8.66$7.40$7.96